Controllers
Contents
Nintendo Wiimote
This includes instructions on installing software and configuration to pair Nintendo Wii Wiimotes using Bluetooth to the Pandora, and using them as joystick controllers. This was done under the base install of Angstrom Linux provided on the Pandora, using Hotfix 4. This does not include setting up a sensor bar type setup, but should allow you to use classic controllers that plug into the Wiimote.
Installing the Drivers
Open a Terminal, and run the command
sudo opkg update
It will give you a warning about responsibility, and asks for your user password. This will update the Angstrom packages stored on NAND.
Then install the Wiimote drivers and software, cwiid, using the command
sudo opkg install cwiid
Pairing the Wiimote
Make sure Bluetooth is enabled. In Hotfix 4, there's a script to "Toggle Bluetooth Status" in the Pandora menu under the "System" category. A light will turn on on the left hand side of the Pandora if Bluetooth is on, next to the network light.
Open a Terminal, and run the command and follow the directions.
wminput
It will tell you to press 1+2 on the Wiimote to connect. On my Wiimotes, the lights flash and the fourth light on the Wiimote lights solid once paired. If you then quit the wminput application (for instance, by hitting CTRL-C), your Wiimote will un-pair and turn off. I usually just hide the Terminal in the background by minimizing the window while I run game emulators.
You can pair multiple Wiimotes, just run wminput a second time and follow the instructions to pair it. I only have two, and both lit the fourth light.
In PicoDrive, the Sega Genesis emulator, in the controller settings, if you push left or right it will display different joysticks configured. You can set up the buttons for different players there. The Wiimotes appeared as joysticks 1 and 2, in the order in which I paired them.
Changing the Wiimote Configuration
You can edit /etc/cwiid/wminput/default and /etc/cwiid/wminput/buttons to map the buttons of the Wiimote. You should quit wminput and restart them for these changes to take effect. They are plain text files. I edited them using vim from the command line, which is not the most user friendly thing to describe. Because they're system files, I needed to use sudo again, so I ran
sudo vim /etc/cwiid/wminput/default
By default, the Wiimote is set up to control the mouse with the accelerometer. This means, as you tilt the Wiimote left and right, your mouse will shift around. I found it a bit distracting, and so I commented out two lines in /etc/cwiid/wminput/default so they look like this:
#Plugin.acc.X = REL_X #Plugin.acc.Y = REL_Y
Also, I use the Wiimote "sideways", like a traditional Nintendo controller. I changed the direction pad to reflect this. Though you can do that within emulator configurations, it seemed handier to just have that set up by default. To do this, make these changes in /etc/cwiid/wminput/buttons
Wiimote.Up = KEY_LEFT Wiimote.Down = KEY_RIGHT Wiimote.Left = KEY_DOWN Wiimote.Right = KEY_UP
It is also possible to map the Wiimote or extension buttons to a virtual gamepad. See below for instructions.
Nintendo Wii Classic Controller
There are two ways to use a Wiimote or Classic Controller with the Pandora:
- As a virtual gamepad. This means you can use it in games that support gamepads, and allows multiplayer in games that support it, but won't work in games that don't support gamepads.
- As a clone of the Pandora's gaming controls, by mapping it to the same keys. This theoretically means it would work in games that don't have gamepad support, or allow you to change the controls at all, as long as they are using the Pandora controls. However, currently, not all games will register the input with this method. SuperTux, OpenTyrian, PandoraPanic and Snes9X4D4P will. Giana's Return, Sqrxz and psx4pandora won't. Additionally, Mupen64Plus with the default PPSP Input Plugin won't - but the Blight Input Plugin will.
As a virtual gamepad
The default profile doesn't have classic controller buttons defined, but cwiid comes with a gamepad profile which does. You can load it in wminput like this using a terminal:
wminput -c gamepad
Then connect your Wiimote and Classic Controller. You do not have to connect the Classic Controller before you connect the Wiimote.
However the analog sticks/dpad seemed to be set up wrong in the gamepad profile (/etc/cwiid/wminput/gamepad):
Classic.Dpad.X = ABS_X Classic.Dpad.Y = ABS_Y Classic.LStick.X = ABS_HAT0X Classic.LStick.Y = ABS_HAT0Y Classic.RStick.X = ABS_HAT1X Classic.RStick.Y = ABS_HAT1Y
should be replaced with:
Classic.Dpad.X = ABS_HAT0X Classic.Dpad.Y = ABS_HAT0Y Classic.LStick.X = ABS_X Classic.LStick.Y = ABS_Y Classic.RStick.X = ABS_RX Classic.RStick.Y = ABS_RY
Otherwise, you won't get proper analog input from the sticks, since PoV hats aren't analog.
As a clone of the Pandora's gaming controls
This method works well where it does, you get a clone of the Pandora's gaming controls (minus the nubs), that should theoretically work in all games that support the Pandora's gaming controls. However, because of differences in how the games receive input, not all will detect the "fake" input.
Here is the profile for the Pandora gaming controls:
# D-Pad Classic.Up = KEY_UP Classic.Down = KEY_DOWN Classic.Left = KEY_LEFT Classic.Right = KEY_RIGHT # Select, Start and Space Classic.Minus = KEY_LEFTCTRL Classic.Plus = KEY_LEFTALT Classic.Home = KEY_SPACE # BXYA on Pandora Classic.A = KEY_END Classic.B = KEY_PAGEDOWN Classic.X = KEY_PAGEUP Classic.Y = KEY_HOME Classic.ZL = KEY_Q Classic.ZR = KEY_P Classic.L = KEY_RIGHTSHIFT Classic.R = KEY_RIGHTCTRL
Save that in /etc/cwiid/wminput - you can name it whatever you want, as long as you load it in wminput using "wminput -c filename" - and make sure to save it using UNIX line endings (LF).
Once the profile is loaded and your Wiimote/Classic Controller is connected, it will automatically work in some games, but not in others. This might be possible to change to work in all games by modifying the wminput source code.
