Difference between revisions of "Hardware hacking"

From Pandora Wiki
Jump to: navigation, search
(How Do I Make a TV-Out Cable?: added new PDF link)
(UART)
Line 49: Line 49:
 
* UART2 and 3 are available via the EXT connector, and via internal solder pads on the latest revision
 
* UART2 and 3 are available via the EXT connector, and via internal solder pads on the latest revision
 
** UART2 appears to support hardware flow control with RTS/CTS lines
 
** UART2 appears to support hardware flow control with RTS/CTS lines
** In the 2.6.27 Kernel UART3 is /dev/ttyS0
+
** On the 2.6.27 Kernel UART3 is /dev/ttyS0
 +
** On 2.6.37 or later, UART2 is accessible through /dev/ttyO1, UART3 is on /dev/ttyO2
  
 
===GPIO===
 
===GPIO===

Revision as of 13:28, 5 May 2012

About custom hardware extensions, see also Kernel interface

Official Hackers Manual

There is a LOT of great information in this: Pandora Hackers Manual v1.01 by MWeston

Pinouts

Here's a list of pinouts for the various connectors and boards.

Here's a pic of the board, some of the pinouts can be seen on it. [1]

Ext Connector

TV cable connector

What does it have?

  • UART2
  • UART3
  • TV out
  • Stereo line out
  • Stereo line in
  • The UART lines can also be used as GPIO (six of them) and PWM lines (four of them).


Where can we get the connectors from?

  • The connector appears to be a Tyco Electronics connector, part number 1717169-2
  • The manufacturer does *not* stock these for engineering samples, and very few vendors carry them
  • Community member WizardStan has ordered a bunch and is selling them at $2 a piece plus shipping from Canada, see here (thread) or here (article)

How Do I Make a TV-Out Cable?

  • There are some useful tips in the EXT Connectors thread.
  • A guide explaining one way of creating the video cables can be found here
  • MarkoeZ Has written a blog post about it here

Battery

Battery.jpg

Internal connections

LCD

  • TD043MTEA1 datasheet
  • LTPS (8-bit parallel input for R, G and B, with separate horizontal and vertical sync)
  • 3.3V?

UART

  • UART2 and 3 are available via the EXT connector, and via internal solder pads on the latest revision
    • UART2 appears to support hardware flow control with RTS/CTS lines
    • On the 2.6.27 Kernel UART3 is /dev/ttyS0
    • On 2.6.37 or later, UART2 is accessible through /dev/ttyO1, UART3 is on /dev/ttyO2

GPIO

  • 6 are available on the EXT connector
  • 7 are internal, 2 of which can be used as extra shoulder buttons
  • 1 located on the LCD cable

JTAG

  • Yes, 1.8V 10-pin (board label JTAG)

I2C

  • One at 1.8V from the OMAP (board label I2C3-1V8)
  • One at 2.8V (board label I2C3-2V8)

USB

  • No internal USB ports

Keypad backlight

  •  ?

Extra LEDs

LED7 and LED8 can be added. You need to add FETs (Q17 and Q18) and resistors (R165, R166, R167 and R168) See the official "Pandora Hacker Guide" from Michael Weston for more details and component values.

Breakout Board

Developer's breakout board
Developer's breakout board

This is the breakout board used by Pandora team members during development. Only a small number were made, and they are not available to the public. However a similar product (or gerber files) may be released in the future. A schematic for this board is available here: http://openpandora.ca/schematic/AV_Board_schematic.pdf