|
|
| (15 intermediate revisions by 10 users not shown) |
| Line 1: |
Line 1: |
| − | ''Please add to this if you have any information''
| + | #redirect [[Hardware_Hacking]] |
| − | ==Official Hackers Manual==
| |
| − | [http://www.openpandora.org/downloads/PANDORA_Hackers_manual_v101.pdf Pandora Hackers Manual v1.01 by MWeston] | |
| − | | |
| − | ==Making an RS232 level converter for the Pandora==
| |
| − | How is this done?
| |
| − | | |
| − | ==Pinouts==
| |
| − | Here's a list of pinouts for the various connectors and boards.
| |
| − | | |
| − | Here's a pic of the board, some of the pinouts can be seen on it. [http://pandorapress.net/files/2010/02/rev5.jpg] Board with many components labeled. [http://www.rspace.eu/pandora/]
| |
| − | | |
| − | ==Ext Connector==
| |
| − | ''What does it have?''
| |
| − | * UART2
| |
| − | * UART3
| |
| − | * TV out
| |
| − | * Stereo line out
| |
| − | * Stereo line in
| |
| − | * The UART lines can also be used as GPIO (six of them) and PWM lines (four of them).
| |
| − | | |
| − | | |
| − | ''What is the pinout?''
| |
| − | | |
| − | * The pinout of the [http://s198.photobucket.com/albums/aa99/MWeston_2007/?action=view¤t=cable_connector.png Ext Connector]
| |
| − | | |
| − | ''Where can we get the connectors from?''
| |
| − | | |
| − | * The connector appears to be a Tyco Electronics connector, part number 1717169-2
| |
| − | * The manufacturer does *not* stock these for engineering samples, and very few vendors carry them
| |
| − | | |
| − | ==Battery==
| |
| − | * 3.7V
| |
| − | * Lithium polymer single cell battery
| |
| − | * 4000 mAH, 4 AH
| |
| − | * battery cover here: [http://www.openpandora.org/images/Battery2.jpg]
| |
| − | * reading out battery information: [[data provided by Battery and Power driver]]
| |
| − | | |
| − | ==Internal connections==
| |
| − | | |
| − | ===LCD===
| |
| − | * LTPS (8-bit parallel input for R, G and B, with separate horizontal and vertical sync)
| |
| − | * 3.3V?
| |
| − | * TD043MTEA2 [http://beyondinfinite.com/lcd/Library/Toppoly/TD043MTEA2.pdf datasheet]
| |
| − | | |
| − | ===UART===
| |
| − | * UART2 and 3 are available via the EXT connector, and via internal solder pads on the latest revision
| |
| − | ** UART2 appears to support hardware flow control with RTS/CTS lines
| |
| − | | |
| − | ===GPIO===
| |
| − | * 6 are available on the EXT connector
| |
| − | * ''Are there any internal?''
| |
| − | ** 7 are internal, 2 of which can be used as extra shoulder buttons
| |
| − | ** 1 located on the LCD cable
| |
| − | | |
| − | ===Battery===
| |
| − | ===JTAG===
| |
| − | * Yes, 1.8V 10-pin (board label JTAG)
| |
| − | | |
| − | ===I<sup>2</sup>C===
| |
| − | * One at 1.8V from the OMAP (board label I2C3-1V8)
| |
| − | * One at 2.8V (board label I2C3-2V8)
| |
| − | | |
| − | === USB ===
| |
| − | * No internal USB ports
| |
| − | | |
| − | ===Keypad backlight===
| |
| − | Maximum current draw?
| |
| − | | |
| − | ==Breakout Board==
| |
| − | [[Image:Breakoutboard.jpg|thumb|alt=Developer's breakout board|Developer's breakout board]]
| |
| − | This is the breakout board used by Pandora team members during development. Only a small number were made, and they are not available to the public. However a similar product (or gerber files) may be released in the future. A schematic for this board is available here: http://openpandora.ca/schematic/AV_Board_schematic.pdf
| |
| − | | |
| − | [[Category:Hardware]]
| |
| − | [[Category:Hacking]]
| |
